Owner: Alvin Fosselman
Location: Newport, PA., USA
Vehicle: 1994 Mazda Miata
Horsepower: 300
Photos By: Alvin Fosselman
ENGINE & PERFORMANCE
FM II turbo kit
Garrett T28 ball bearing turbo ceramic coated
FM cast exhaust manifold ceramic coated
FM front mount intercooler
FM 2.5” down pipe ceramic coated
FM blow-off valve
Link ECU with knock sensor, air temp sensor, boost controller
550cc RC injectors
HKS red air filter
Custom built intake manifold with a custom 70mm throttle body
Painted body color
Custom intake manifold
Thermal gasket
M Tuned fuel rail
Aeromotive fuel regulated with psi gauge
Walbro 255 fuel pump
99 Miata head swap
Port and polished and 5 angle valve job
Supertech 1mm over valves
Supertech valve springs
ARP head studs
Gates racing timing belt
Fidanza cam pulleys
Built engine with Carrillo H-Beam rods
Wiseco 9:1 pistons
Lightened, balanced, nitro coated crankshaft
ARP main studs
ATI crank pulley
I.J. crank scraper
ACL Race bearings
Boundary Engineering oil pump
6 speed trans swap
Modified Steeda
Short throw shifter to work with 6 speed trans
Fidanza 8lb aluminum flywheel
ACT stage 3 clutch
Hi-Flow catalytic convertor
Custom built stainless center exit exhaust
CX Racing 2 core radiator and fan shroud
Samco silicone radiator hoses
Coil on plug conversion and NGK Iridium plugs
Apexi turbo timer
Valve cover shaved smooth and painted body color
Custom carbon fiber valve cover
PLX wideband O2 sensor
Greddy oil and radiator cap
WHEELS & TIRES
17x8 Custom built I Forged Aeros wheels (front)
17x10 Custom built I Forged Aeros wheels (rear)
Painted lips body color with powder coated black spokes
225/40/17 Nitto NT555 tires (front)
255/40/17 Nitto NT555 tires (rear)
SUSPENSION
FM frame rail reinforcement kit with butterfly brace
1.5” FM lowering springs
KYB AGX 8-way adjustable shocks
FM rear shock mounts
Super Pro offset bushings
Front and rear control arms
Custom built 3-point front shock tower brace and rear brace
TC Sportline upper front and rear adjustable control arms
Front sub frame lower brace
BRAKES
Custom built big brake kit
Wilwood 4 piston front calipers
Corvette ZR1 rear calipers
Custom built rotor hubs
12.5” Wilwood cross drilled rotors
Front and rear custom built caliper brackets
Braided stainless brake lines
Wilwood adjustable brake
Proportioning valve
Dot 5 brake fluid
EXTERIOR
Garage Vary Tail light panel with shaved lock and back up light Molded in AWR fender flares
1.75” front 2.5” rear Altered VIS body kit
Side skirts molded on
Shaved body lines, door handles, locks, antenna, emblems, windshield washer nozzles, stock side mirrors
Shaved engine bay with wire and hose tuck
Custom wiper cowl and radiator covers
Reverse open hood
Altered RX-7 side mirrors and Lexan wing windows
Custom made carbon/orange kevlar fiber hood, headlight covers, windshield pillar, rear deck, trunk lid, gas lid
Cobalt low profile headlight kit
Hella fog light
Smoked front parking lights
Smoked tail lights
Robbins cloth convertible top
INTERIOR
JDM right hand drive swap with JDM gauge cluster
Carbon fiber dash, top of doors, door trim and gauge trim
Carbon fiber/orange kevlar door bottoms, gauge trim, windshield banner
Suede wrapped dash, dash panels, windshield trim
Corbeau Forza suede race seats
Corbeau seat mounting brackets
Corbeau seat belt pads
G-force racing race seat belts
Hard Dog extreme roll bar
Custom built seat belt mounting bar
Momo steering wheel, short carbon fiber shift knob
NRG short steering wheel hub with NRG quick tilt release hub
Auto Meter gauges boost, exhaust temp, volt, oil temp, air/fuel
Suede shift boot
AUDIO & MULTIMEDIA
Clarion in dash 7” touch screen CD/DVD player and Clarion 7 band equalizer
Cadence Amadeus 4x100 watts digital amplifier
6.5" Cadence ZX series components
4x 8" Kicker Comp subwoofers
Custom built carbon fiber subwoofer box
